DITEC GLOBE Service Manual

Installation and maintenance manual for automations for sectional overhead doors and spring balanced up-and-over doors.(Original instructions)GLOBEIP1

10IP1839EN • 2012-07-317. ASSEMBLING THE AUTOMATION- Insert the guide [B] into the non-bevelled side of the coupling [C] until it reaches the sto

11IP1839EN • 2012-07-318. TENSIONING BELT AND CHAIN- Assemble the transmission unit as indicated in the gure.- To tension the chain or belt

12IP1839EN • 2012-07-319. MECHANICAL INSTALLATION- Select and mark the point where the guide will be mounted on the wall and ceiling.- Leavin

13IP1839EN • 2012-07-3110. FASTENING THE ARM- Mount the door section retention bracket [A] on the top of the door, using the reinforcement angle

14IP1839EN • 2012-07-3111. INSTALLATION OF THE END STOPS- Insert the opening end stop [A] in the guide [B], as shown in the gure, and fasten it

15IP1839EN • 2012-07-3113. INSTALLATION OF THE GLOBEC ADAPTER FOR UP-AND-OVER DOORSmax 210min 20min 900

16IP1839EN • 2012-07-3114. INSTALLATION OF THE GLOBESI INTERMEDIATE SUPPORT12205030 75212

17IP1839EN • 2012-07-3115. ELECTRICAL CONNECTIONSThe gure shows the main connections of the control panel 70R-71R.-+Output 24 V= / max 0.3 AStopSafe

18IP1839EN • 2012-07-3116. COMMANDSCommand Function Description1 5 N.O. STEP-BY-STEP With DIP1=OFF, the closing of the contact activates opening or

19IP1839EN • 2012-07-3117. OUTPUTS AND ACCESSORIESOutput Value - Accessories Description4901 23+-24 V= / 0.3 AAccessories power supply. Power supply

2IP1839EN • 2012-07-31INDEXSubject Page1. General safety precautions 32. Declaration of incorporation of partly completed machinery 42.1 Machinery

20IP1839EN • 2012-07-3118. ADJUSTMENTSDescription OFF ONDIP1 Command 1-5 operation.NOTE: it also sets operating mode of the plugin cards connected on

21IP1839EN • 2012-07-31LED On FlashingSIGTransmitter enabling/storage phase. Reception of a radio transmission.Cancellation of transmitters in progres

22IP1839EN • 2012-07-3119. RADIO RECEIVER OPERATIONThe control panel is equipped with a radio receiver with a frequency of 433.92 MHz. The antenna co

23IP1839EN • 2012-07-3120. START-UPWARNING The operations related to point 5 are performed without safeties. The trimmer can only be adjusted wit

24IP1839EN • 2012-07-3121. TROUBLESHOOTINGProblem Possible causes RemedyThe automation does not open or close.No power.(POWER ALARM led off).Check tha

25IP1839EN • 2012-07-3123.1 General safety precautionsThe following precautions are an integral and essential part of the product and must be supplied

26IP1839EN • 2012-07-31DETACH AND DELIVER TO THE CUSTOMERInstaller:DITEC S.p.A.Via Mons. Banfi, 321042 Caronno Pertusella (VA) - ITALYTel. +39 02 9639

27IP1839EN • 2012-07-31

TMDITEC S.p.A. Via Mons. Ban, 3 21042 Caronno P.lla (VA) Italy Tel. +39 02 963911 Fax +39 02 9650314www.ditec.it [email protected] BELGI

3IP1839EN • 2012-07-311. GENERAL SAFETY PRECAUTIONSThis installation manual is intended for professionally competent personnel only.Installation, ele

4IP1839EN • 2012-07-312. DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY(Directive 2006/42/EC, Annex II-B)The manufacturer DITEC S.p.A. wi

5IP1839EN • 2012-07-313. TECHNICAL DATAGLOBE7 GLOBE10Power supply 230 V~ / 50-60 Hz 230 V~ / 50-60 HzAbsorption 0,7 A 1,2 AThrust 500 N 900 NOpening

6IP1839EN • 2012-07-313.2 DimensionsNOTE: unless otherwise specied, all measurements are expressed in millimetres (mm).i2081244903.1 Operating instr

7IP1839EN • 2012-07-314. STANDARD INSTALLATIONRef. Code Description1 GLOBE7GLOBE10Motor + control panel2 GLOBEL1GLOBELV1GLOBESIExtension set for chai

8IP1839EN • 2012-07-315. MAIN COMPONENTSRef. Code Description1 24 V= motor with encoder2 Fastening bracket3 Slide carriage4 Sliding guide5 Fastening

9IP1839EN • 2012-07-316. ASSEMBLING BELT AND CHAIN- Attach the belt or chain [A] to the transmission [B] and slide [C].- Assemble the belt st